|
Linux altinda USB Modem Kurulumu USB modem sahipleri: artik linux'da usb modem'i olupta internete giremiyorum diyen kalmasin.. kurulum dökümanını size adim adim asagida anlaticam.. kolay gelsin.. 1. Adim : cxacru-fw.bin ; isimli dosyamizi önce download ediyoruz.. PHP- Kodu: PHP- Kodu: PHP- Kodu: 2. Adim : rp-pppoe 'yi indiriyoruz PHP- Kodu: PHP- Kodu: PHP- Kodu: ve PHP- Kodu: Burada sizden pppoe baglanisi icin bilgileri istenecektir. * Kullanıcı adı ve parola istemi icim Türk Telekom'dan aldığınız şekilde girin. Örnek : time2burn@ttnet * Password istemine : ttnet'ten almis oldugunuz sifreyi girin. * interface için sorulan kısma '' nas0 '' yazin. (tirnak isaretleri haric) * DNS sorusu icin '' server '' yazin. (tirnak isaretleri haric) * firewall sorucu icin " 0 " yazın.. (sıfır) - (Tırnak isaretleri haric) * sorulan diger soruları " enter " ile gecin.. Dipnot ; PHP- Kodu: PHP- Kodu: cift tilayarak install veya konsoldan / terminalden PHP- Kodu: 3. Adim : Daha sonra masaüstü'ne '' cxacru '' isminde bos bir metin belgesi olusturun.. icine asagidakileri aynen copy/paste edin kaydedin (Ctrl + S) ve cikin.. PHP- Kodu: 4. Adim br2684ctl indiriyoruz.. PHP- Kodu: PHP- Kodu: Asagidaki hatayi aliyorsaniz ; PHP- Kodu: PHP- Kodu: PHP- Kodu: Root olarak, PHP- Kodu: PHP- Kodu: Kaynak = Kendim :) |
Yanıt: Linux altinda USB Modem Kurulumu Ethernet Interface: nas0 User name: xxxxx@ttnet Activate-on-demand: Yes; idle timeout = server seconds DNS addresses: Supplied by ISP's server Firewalling: NONE >>> Accept these settings and adjust configuration files (y/n)? y Adjusting /etc/ppp/pppoe.conf Adjusting /etc/ppp/pap-secrets and /etc/ppp/chap-secrets (But first backing it up to /etc/ppp/pap-secrets-bak) (But first backing it up to /etc/ppp/chap-secrets-bak) Congratulations, it should be all set up! Type 'pppoe-start' to bring up your PPPoE link and 'pppoe-stop' to bring it down. Type 'pppoe-status' to see the link status. sudo br2684ctl -c 0 -b -a 8.35 br2684ctl[21822]: Interface "nas0" could not be created, reason: File exists br2684ctl[21822]: Communicating over ATM 0.8.35, encapsulation: LLC br2684ctl[21822]: Could not configure interface:File exists sudo pppoe-start dediğim zaman da timeout cevabı geliyor harfi harfiyen uyguladım dedinkerinizi sorun nedir yardımcı olmanız mumkunmu acaba arkadaslar |
Cevap: Linux altinda USB Modem Kurulumu Normalde eğer dediklerimi eksiksiz yapmışsanız bağlanmanız lazım. Kurulumu tekrar ve dikkatlice tekrar yap. ve bağlanmada önce X'i resetle. Bu arada, Linux dagitimin Windows ile ayni makinada mi ? Modem isiklarinin dogru yanip yanmadigina dikkat et. Daha once basima gelmisti, Windows ile oturum acmadan, direk linux ile giris yaptigim zaman Linux uzerinden USB modem ile nete baglanamiyordum. Baglanamabilmem icin, Once Windows ile oturup acip, makinaya reset atip Linux ile giris yapmam gerekiyordu. Ancak demis oldugum gibi buda bir ihtimal sen oncelik olarak demis oldugum gibi, kurulumu dikkatli bir sekilde tekrar gerceklestir, X'i restartla ve girdikten sonra baglanmayi dene. Mutlaka birsey atlamis olmalisin. Kolay Gelsin. |
Yanıt: Linux altinda USB Modem Kurulumu Running ./configure... checking for gcc... gcc checking for C compiler default output file name... a.out checking whether the C compiler works... yes checking whether we are cross compiling... no checking for suffix of executables... checking for suffix of object files... o checking whether we are using the GNU C compiler... yes checking whether gcc accepts -g... yes checking for gcc option to accept ANSI C... none needed checking for ranlib... ranlib checking how to run the C preprocessor... gcc -E checking for egrep... grep -E checking for ANSI C header files... yes checking for sys/wait.h that is POSIX.1 compatible... yes checking for sys/types.h... yes checking for sys/stat.h... yes checking for stdlib.h... yes checking for string.h... yes checking for memory.h... yes checking for strings.h... yes checking for inttypes.h... yes checking for stdint.h... yes checking for unistd.h... yes checking fcntl.h usability... yes checking fcntl.h presence... yes checking for fcntl.h... yes checking sys/dlpi.h usability... no checking sys/dlpi.h presence... no checking for sys/dlpi.h... no checking sys/ioctl.h usability... yes checking sys/ioctl.h presence... yes checking for sys/ioctl.h... yes checking sys/time.h usability... yes checking sys/time.h presence... yes checking for sys/time.h... yes checking syslog.h usability... yes checking syslog.h presence... yes checking for syslog.h... yes checking for unistd.h... (cached) yes checking net/if_arp.h usability... yes checking net/if_arp.h presence... yes checking for net/if_arp.h... yes checking netinet/if_ether.h usability... yes checking netinet/if_ether.h presence... yes checking for netinet/if_ether.h... yes checking getopt.h usability... yes checking getopt.h presence... yes checking for getopt.h... yes checking sys/uio.h usability... yes checking sys/uio.h presence... yes checking for sys/uio.h... yes checking sys/param.h usability... yes checking sys/param.h presence... yes checking for sys/param.h... yes checking for fcntl.h... (cached) yes checking net/bpf.h usability... no checking net/bpf.h presence... no checking for net/bpf.h... no checking netpacket/packet.h usability... yes checking netpacket/packet.h presence... yes checking for netpacket/packet.h... yes checking net/ethernet.h usability... yes checking net/ethernet.h presence... yes checking for net/ethernet.h... yes checking asm/types.h usability... yes checking asm/types.h presence... yes checking for asm/types.h... yes checking linux/if_packet.h usability... yes checking linux/if_packet.h presence... yes checking for linux/if_packet.h... yes checking linux/if_ether.h usability... yes checking linux/if_ether.h presence... yes checking for linux/if_ether.h... yes checking sys/socket.h usability... yes checking sys/socket.h presence... yes checking for sys/socket.h... yes checking sys/cdefs.h usability... yes checking sys/cdefs.h presence... yes checking for sys/cdefs.h... yes checking net/if.h usability... yes checking net/if.h presence... yes checking for net/if.h... yes checking net/if_dl.h usability... no checking net/if_dl.h presence... no checking for net/if_dl.h... no checking net/if_ether.h usability... no checking net/if_ether.h presence... no checking for net/if_ether.h... no checking net/if_types.h usability... no checking net/if_types.h presence... no checking for net/if_types.h... no checking for netinet/if_ether.h... (cached) yes checking for net/if_types.h... (cached) no checking for net/if_dl.h... (cached) no checking for linux/if.h... yes checking for linux/if_pppox.h... no checking for an ANSI C-conforming const... yes checking for pid_t... yes checking whether time.h and sys/time.h may both be included... yes checking whether struct tm is in sys/time.h or time.h... time.h checking for struct sockaddr_ll... yes checking for N_HDLC line discipline... no checking for working memcmp... yes checking for function prototypes... yes checking whether setvbuf arguments are reversed... no checking return type of signal handlers... void checking for select... yes checking for socket... yes checking for strerror... yes checking for strtol... yes checking for a BSD-compatible install... /usr/bin/install -c checking for unsigned short... yes checking size of unsigned short... 2 checking for unsigned int... yes checking size of unsigned int... 4 checking for unsigned long... yes checking size of unsigned long... 4 checking for pppd... /usr/sbin/pppd checking for echo... /bin/echo checking for setsid... /usr/bin/setsid checking for id... /usr/bin/id checking for Linux 2.4.X kernel-mode PPPoE support... no checking packing order of bit fields... reversed configure: creating ./config.status config.status: creating Makefile config.status: creating libevent/Makefile config.status: creating ../scripts/pppoe-connect config.status: creating ../scripts/pppoe-start config.status: creating ../scripts/pppoe-stop config.status: creating ../scripts/pppoe-init config.status: creating ../scripts/pppoe-init-suse config.status: creating ../scripts/pppoe-init-turbolinux config.status: creating ../scripts/pppoe-setup config.status: creating ../gui/Makefile config.status: creating ../gui/tkpppoe config.status: creating config.h config.status: config.h is unchanged On this platform, the following targets will be built: pppoe pppoe-server pppoe-sniff pppoe-relay Type 'make' to compile the software. Running make... Type 'make install' as root to install the software. Running make install... Type 'make install' as root to install the software. mkdir -p /usr/sbin /usr/bin/install -c -m 755 pppoe /usr/sbin /usr/bin/install -c -m 755 pppoe-server /usr/sbin if test -x licensed-only/pppoe-server-control ; then /usr/bin/install -c -m 755 licensed-only/pppoe-server-control /usr/sbin; fi if test -x pppoe-relay ; then /usr/bin/install -c -m 755 pppoe-relay /usr/sbin; fi if test -x pppoe-sniff; then /usr/bin/install -c -m 755 pppoe-sniff /usr/sbin; fi /usr/bin/install -c -m 755 ../scripts/pppoe-connect /usr/sbin /usr/bin/install -c -m 755 ../scripts/pppoe-start /usr/sbin /usr/bin/install -c -m 755 ../scripts/pppoe-status /usr/sbin /usr/bin/install -c -m 755 ../scripts/pppoe-stop /usr/sbin /usr/bin/install -c -m 755 ../scripts/pppoe-setup /usr/sbin mkdir -p /usr/share/doc/rp-pppoe-3.8 /usr/bin/install -c -m 644 ../doc/CHANGES /usr/share/doc/rp-pppoe-3.8 /usr/bin/install -c -m 644 ../doc/KERNEL-MODE-PPPOE /usr/share/doc/rp-pppoe-3.8 /usr/bin/install -c -m 644 ../doc/HOW-TO-CONNECT /usr/share/doc/rp-pppoe-3.8 /usr/bin/install -c -m 644 ../doc/LICENSE /usr/share/doc/rp-pppoe-3.8 /usr/bin/install -c -m 644 ../README /usr/share/doc/rp-pppoe-3.8 /usr/bin/install -c -m 644 ../SERVPOET /usr/share/doc/rp-pppoe-3.8 /usr/bin/install -c -m 644 ../configs/pap-secrets /usr/share/doc/rp-pppoe-3.8 mkdir -p /usr/man/man8 for i in pppoe pppoe-server pppoe-sniff pppoe-relay ; do \ if test -f ../man/$i.8 ; then \ /usr/bin/install -c -m 644 ../man/$i.8 /usr/man/man8 || exit 1; \ fi; \ done /usr/bin/install -c -m 644 ../man/pppoe-start.8 /usr/man/man8 /usr/bin/install -c -m 644 ../man/pppoe-stop.8 /usr/man/man8 /usr/bin/install -c -m 644 ../man/pppoe-status.8 /usr/man/man8 /usr/bin/install -c -m 644 ../man/pppoe-connect.8 /usr/man/man8 /usr/bin/install -c -m 644 ../man/pppoe-setup.8 /usr/man/man8 mkdir -p /usr/man/man5 /usr/bin/install -c -m 644 ../man/pppoe.conf.5 /usr/man/man5 mkdir -p /etc/ppp mkdir -p /etc/ppp/plugins echo "# Directory created by rp-pppoe for kernel-mode plugin" > /etc/ppp/plugins/README NOT overwriting existing /etc/ppp/pppoe.conf NOT overwriting existing /etc/ppp/firewall-standalone NOT overwriting existing /etc/ppp/firewall-masq NOT overwriting existing /etc/ppp/pppoe-server-options # L2TP Type 'pppoe-setup' to configure the software. Welcome to the Roaring Penguin PPPoE client setup. First, I will run some checks on your system to make sure the PPPoE client is installed properly... Looks good! Now, please enter some information: USER NAME >>> Enter your PPPoE user name (default xxxxxxxxxx@ttnet): INTERFACE >>> Enter the Ethernet interface connected to the DSL modem For Solaris, this is likely to be something like /dev/hme0. For Linux, it will be ethn, where 'n' is a number. (default nas0): Do you want the link to come up on demand, or stay up continuously? If you want it to come up on demand, enter the idle time in seconds after which the link should be dropped. If you want the link to stay up permanently, enter 'no' (two letters, lower-case.) NOTE: Demand-activated links do not interact well with dynamic IP addresses. You may have some problems with demand-activated links. >>> Enter the demand value (default server): DNS Please enter the IP address of your ISP's primary DNS server. If your ISP claims that 'the server will provide DNS addresses', enter 'server' (all lower-case) here. If you just press enter, I will assume you know what you are doing and not modify your DNS setup. >>> Enter the DNS information here: server PASSWORD >>> Please enter your PPPoE password: >>> Please re-enter your PPPoE password: FIREWALLING Please choose the firewall rules to use. Note that these rules are very basic. You are strongly encouraged to use a more sophisticated firewall setup; however, these will provide basic security. If you are running any servers on your machine, you must choose 'NONE' and set up firewalling yourself. Otherwise, the firewall rules will deny access to all standard servers like Web, e-mail, ftp, etc. If you are using SSH, the rules will block outgoing SSH connections which allocate a privileged source port. The firewall choices are: 0 - NONE: This script will not set any firewall rules. You are responsible for ensuring the security of your machine. You are STRONGLY recommended to use some kind of firewall rules. 1 - STANDALONE: Appropriate for a basic stand-alone web-surfing workstation 2 - MASQUERADE: Appropriate for a machine acting as an Internet gateway for a LAN >>> Choose a type of firewall (0-2): 0 ** Summary of what you entered ** Ethernet Interface: nas0 User name: xxxxxxxxxxxx@ttnet Activate-on-demand: Yes; idle timeout = server seconds DNS addresses: Supplied by ISP's server Firewalling: NONE >>> Accept these settings and adjust configuration files (y/n)? y Adjusting /etc/ppp/pppoe.conf Adjusting /etc/ppp/pap-secrets and /etc/ppp/chap-secrets (But first backing it up to /etc/ppp/pap-secrets-bak) (But first backing it up to /etc/ppp/chap-secrets-bak) Congratulations, it should be all set up! Type 'pppoe-start' to bring up your PPPoE link and 'pppoe-stop' to bring it down. Type 'pppoe-status' to see the link status. root@xxxxx-laptop:~/Masaüstü/Usb Modem /rp-pppoe-3.8# cd root@xxxxx-laptop:~# |
Yanıt: Linux altinda USB Modem Kurulumu 5959 ? S 0:00 br2684ctl -c 0 -b -a 8.35 5968 pts/0 S 0:00 /bin/sh /usr/sbin/pppoe-connect baglanmıyorr maleseff dediklerini yaptım birde sen kontrol et istersen |
Cevap: Linux altinda USB Modem Kurulumu görüldügü kadariyla derlemede bir problem yok, xxxxxxxxxx@ttnet kismina ttnet kullanici adin mi yazili yoksa editleme mi yaptin ? modemin isiklari dogru sekilde yaniyor mu ? herkesi eksiksiz yaptim diyorsan, birde windows ile oturum ac istersen (eger kuruluysa) demis oldugum gibi, boyle bir sorun vardi ilk mesajimda belirtmis oldugum gibi bende usb modem ile windows da oturum acmadan once linux uzerinden nete baglanamiyordum. ayrica usb modemin conexant chipsetli mi ? markasi nedir. |
Yanıt: Linux altinda USB Modem Kurulumu xxxxxxxxx@ttnet kısmında x lerin yerinde kullanıcı adımı yazdım tabiki gorunmemesi acısından foruma yazarken onları xx diye yazdım foruma dediğin gibi de yaptım windowsu actım bakandı tekrardan kapadım ve ubuntu 8.04 u actım balamayı denedim ondada basarılı olamadım modemiimin markasıı zoom adsl mode ethernet girisi falan yok sadece tek bir usb girisi mevcut modemde |
Yanıt: Linux altinda USB Modem Kurulumu modemin ısıkları dogru calısıyor onuda yazmayı unutmusum link ısığı normal yaniyor data sekmesi yanmiyorr sadece |
Cevap: Linux altinda USB Modem Kurulumu peki windows ile oturum açtıktan sonra, windows üzerinden nete bağlandın mı bir defa ? windows üzerinden bağlanmayı dene ve daha sonra Linux'a geçip bağlanmayı dene. data sekmesi windows üzerinden nete bağlanırken yanıyor mu peki ? |
Yanıt: Linux altinda USB Modem Kurulumu modemin tam markası zoom adsl usb modem 5510 |
| Tüm Zamanlar GMT +3 Olarak Ayarlanmış. Şuanki Zaman: 10:52. |
Powered by vBulletin® Version 3.8.8 Beta 3
Copyright ©2000 - 2024, vBulletin Solutions, Inc.
Search Engine Friendly URLs by vBSEO
Copyright ©2004 - 2024 IRCForumlari.Net